[OpenWrt-Devel] [PATCH v2] ar71xx: add qihoo 360 c301 router support
Weijie Gao
hackpascal at gmail.com
Thu Sep 11 10:17:55 EDT 2014
Qihoo 360 C301 is a dual band wireless router supports 802.11n and 802.11ac.
Its chipset is AR9344 + AR9882 with two 16MB flashes.
This patch adds its initial support.
v2:
* use mtd_get_mac_ascii to fetch MAC address for ath10k.
* use ath79_register_pci to initialize AR9882.
Signed-off-by: Weijie Gao <hackpascal at gmail.com>
---
target/linux/ar71xx/base-files/etc/diag.sh | 3 +
.../ar71xx/base-files/etc/uci-defaults/01_leds | 4 +
.../ar71xx/base-files/etc/uci-defaults/02_network | 1 +
target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +
.../lib/preinit/81_load_ath10k_board_bin | 17 +++
.../ar71xx/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ar71xx/config-3.10 | 1 +
target/linux/ar71xx/config-3.14 | 1 +
.../ar71xx/files/arch/mips/ath79/mach-qihoo-c301.c | 166 +++++++++++++++++++++
target/linux/ar71xx/generic/profiles/qihoo.mk | 16 ++
target/linux/ar71xx/image/Makefile | 3 +
.../601-MIPS-ath79-add-more-register-defines.patch | 3 +-
...726-MIPS-ath79-add-qihoo-360-c301-support.patch | 40 +++++
.../601-MIPS-ath79-add-more-register-defines.patch | 3 +-
...726-MIPS-ath79-add-qihoo-360-c301-support.patch | 40 +++++
15 files changed, 300 insertions(+), 2 deletions(-)
create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-qihoo-c301.c
create mode 100644 target/linux/ar71xx/generic/profiles/qihoo.mk
create mode 100644 target/linux/ar71xx/patches-3.10/726-MIPS-ath79-add-qihoo-360-c301-support.patch
create mode 100644 target/linux/ar71xx/patches-3.14/726-MIPS-ath79-add-qihoo-360-c301-support.patch
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index 1864b11..c16b7d7 100755
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -166,6 +166,9 @@ get_status_led() {
oolite)
status_led="oolite:red:system"
;;
+ qihoo-c301)
+ status_led="qihoo:green:status"
+ ;;
tew-632brp)
status_led="tew-632brp:green:status"
;;
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
index d3b766d..9d2cd41 100755
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/01_leds
@@ -191,6 +191,10 @@ om5p)
ucidef_set_led_netdev "port2" "port2" "om5p:blue:lan" "eth1"
;;
+qihoo-c301)
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "qihoo:red:status" "phy1tpt"
+ ;;
+
smart-300)
ucidef_set_led_netdev "wan" "WAN" "nc-link:green:wan" "eth0"
ucidef_set_led_switch "lan1" "LAN1" "nc-link:green:lan1" "switch0" "0x04"
diff --git a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
index c5cfd67..d5a43bd 100755
--- a/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
+++ b/target/linux/ar71xx/base-files/etc/uci-defaults/02_network
@@ -346,6 +346,7 @@ hiwifi-hc6361 |\
ja76pf |\
mynet-n600 |\
oolite |\
+qihoo-c301 |\
rb-750 |\
rb-751 |\
tew-632brp |\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 1e96b6d..1c685c6 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -430,6 +430,9 @@ ar71xx_board_detect() {
*PB92)
name="pb92"
;;
+ *"Qihoo 360 C301")
+ name="qihoo-c301"
+ ;;
*"RouterBOARD 411/A/AH")
name="rb-411"
;;
diff --git a/target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin b/target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin
index a28932f..2c06d7f 100644
--- a/target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin
+++ b/target/linux/ar71xx/base-files/lib/preinit/81_load_ath10k_board_bin
@@ -24,6 +24,23 @@ do_load_ath10k_board_bin() {
bs=1 skip=20492 count=2104 >> /tmp/ath10k-board.bin
;;
+ qihoo-c301)
+ local mac
+
+ mac=$(mtd_get_mac_ascii devdata wlan5mac)
+
+ if [ -z "$mac" ]; then
+ mac=$(macaddr_add $(cat /sys/class/net/eth0/address) -2)
+ fi
+
+ dd if=/dev/mtdblock10 \
+ bs=1 skip=20480 count=6 \
+ of=/tmp/ath10k-board.bin
+ macaddr_2bin $mac >> /tmp/ath10k-board.bin
+ dd if=/dev/mtdblock10 \
+ bs=1 skip=20492 count=2104 >> /tmp/ath10k-board.bin
+
+ ;;
esac
[ -f /tmp/ath10k-board.bin ] || {
return
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 846954c..6122d45 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -225,6 +225,7 @@ platform_check_image() {
return 1
;;
+ qihoo-c301 | \
mynet-n600 | \
mynet-n750)
[ "$magic_long" != "5ea3a417" ] && {
diff --git a/target/linux/ar71xx/config-3.10 b/target/linux/ar71xx/config-3.10
index 9a8378a..48ff491 100644
--- a/target/linux/ar71xx/config-3.10
+++ b/target/linux/ar71xx/config-3.10
@@ -72,6 +72,7 @@ CONFIG_ATH79_MACH_OM5P=y
CONFIG_ATH79_MACH_PB42=y
CONFIG_ATH79_MACH_PB44=y
CONFIG_ATH79_MACH_PB92=y
+CONFIG_ATH79_MACH_QIHOO_C301=y
# CONFIG_ATH79_MACH_RB2011 is not set
# CONFIG_ATH79_MACH_RB4XX is not set
# CONFIG_ATH79_MACH_RB750 is not set
diff --git a/target/linux/ar71xx/config-3.14 b/target/linux/ar71xx/config-3.14
index c642913..0996ccb 100644
--- a/target/linux/ar71xx/config-3.14
+++ b/target/linux/ar71xx/config-3.14
@@ -73,6 +73,7 @@ CONFIG_ATH79_MACH_OM5P=y
CONFIG_ATH79_MACH_PB42=y
CONFIG_ATH79_MACH_PB44=y
CONFIG_ATH79_MACH_PB92=y
+CONFIG_ATH79_MACH_QIHOO_C301=y
# CONFIG_ATH79_MACH_RB2011 is not set
# CONFIG_ATH79_MACH_RB4XX is not set
# CONFIG_ATH79_MACH_RB750 is not set
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-qihoo-c301.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-qihoo-c301.c
new file mode 100644
index 0000000..08a602f
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-qihoo-c301.c
@@ -0,0 +1,166 @@
+/*
+ * Qihoo 360 C301 board support
+ *
+ * Copyright (C) 2013 Gabor Juhos <juhosg at openwrt.org>
+ * Copyright (C) 2014 Weijie Gao <hackpascal at gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/pci.h>
+#include <linux/phy.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-spi.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "nvram.h"
+
+#define QIHOO_C301_GPIO_LED_STATUS_GREEN 0
+#define QIHOO_C301_GPIO_LED_STATUS_RED 11
+
+#define QIHOO_C301_GPIO_LED_WAN 1
+#define QIHOO_C301_GPIO_LED_LAN1 2
+#define QIHOO_C301_GPIO_LED_LAN2 3
+#define QIHOO_C301_GPIO_ETH_LEN_EN 18
+
+#define QIHOO_C301_GPIO_BTN_RESET 16
+
+#define QIHOO_C301_GPIO_USB_POWER 19
+
+#define QIHOO_C301_GPIO_SPI_CS1 12
+
+#define QIHOO_C301_GPIO_EXTERNAL_LNA0 14
+#define QIHOO_C301_GPIO_EXTERNAL_LNA1 15
+
+#define QIHOO_C301_KEYS_POLL_INTERVAL 20 /* msecs */
+#define QIHOO_C301_KEYS_DEBOUNCE_INTERVAL \
+ (3 * QIHOO_C301_KEYS_POLL_INTERVAL)
+
+#define QIHOO_C301_WMAC_CALDATA_OFFSET 0x1000
+
+#define QIHOO_C301_NVRAM_ADDR 0x1f058010
+#define QIHOO_C301_NVRAM_SIZE 0x7ff0
+
+static struct gpio_led qihoo_c301_leds_gpio[] __initdata = {
+ {
+ .name = "qihoo:green:status",
+ .gpio = QIHOO_C301_GPIO_LED_STATUS_GREEN,
+ .active_low = 1,
+ },
+ {
+ .name = "qihoo:red:status",
+ .gpio = QIHOO_C301_GPIO_LED_STATUS_RED,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button qihoo_c301_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = QIHOO_C301_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = QIHOO_C301_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+struct flash_platform_data flash __initdata = {NULL, NULL, 0};
+
+static void qihoo_c301_get_mac(const char *name, char *mac)
+{
+ u8 *nvram = (u8 *) KSEG1ADDR(QIHOO_C301_NVRAM_ADDR);
+ int err;
+
+ err = ath79_nvram_parse_mac_addr(nvram, QIHOO_C301_NVRAM_SIZE,
+ name, mac);
+ if (err)
+ pr_err("no MAC address found for %s\n", name);
+}
+
+static void __init qihoo_c301_setup(void)
+{
+ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+ u8 tmpmac[ETH_ALEN];
+
+ ath79_register_m25p80_multi(&flash);
+
+ ath79_gpio_function_enable(AR934X_GPIO_FUNC_JTAG_DISABLE);
+
+ ath79_gpio_output_select(QIHOO_C301_GPIO_LED_WAN,
+ AR934X_GPIO_OUT_LED_LINK4);
+ ath79_gpio_output_select(QIHOO_C301_GPIO_LED_LAN1,
+ AR934X_GPIO_OUT_LED_LINK1);
+ ath79_gpio_output_select(QIHOO_C301_GPIO_LED_LAN2,
+ AR934X_GPIO_OUT_LED_LINK2);
+
+ ath79_gpio_output_select(QIHOO_C301_GPIO_SPI_CS1,
+ AR934X_GPIO_OUT_SPI_CS1);
+
+ gpio_request_one(QIHOO_C301_GPIO_ETH_LEN_EN,
+ GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED,
+ "Ethernet LED enable");
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(qihoo_c301_leds_gpio),
+ qihoo_c301_leds_gpio);
+
+ ath79_register_gpio_keys_polled(-1, QIHOO_C301_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(qihoo_c301_gpio_keys),
+ qihoo_c301_gpio_keys);
+
+ ath79_wmac_set_ext_lna_gpio(0, QIHOO_C301_GPIO_EXTERNAL_LNA0);
+ ath79_wmac_set_ext_lna_gpio(1, QIHOO_C301_GPIO_EXTERNAL_LNA1);
+
+ qihoo_c301_get_mac("wlan24mac=", tmpmac);
+ ath79_register_wmac(art + QIHOO_C301_WMAC_CALDATA_OFFSET, tmpmac);
+
+ ath79_register_pci();
+
+ ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_SW_ONLY_MODE |
+ AR934X_ETH_CFG_SW_PHY_SWAP);
+
+ ath79_register_mdio(1, 0x0);
+
+ /* LAN */
+ qihoo_c301_get_mac("lanmac=", ath79_eth1_data.mac_addr);
+
+ /* GMAC1 is connected to the internal switch */
+ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+
+ ath79_register_eth(1);
+
+ /* WAN */
+ qihoo_c301_get_mac("wanmac=", ath79_eth0_data.mac_addr);
+
+ /* GMAC0 is connected to the PHY4 of the internal switch */
+ ath79_switch_data.phy4_mii_en = 1;
+ ath79_switch_data.phy_poll_mask = BIT(0);
+
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ath79_eth0_data.phy_mask = BIT(0);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
+
+ ath79_register_eth(0);
+
+ gpio_request_one(QIHOO_C301_GPIO_USB_POWER,
+ GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED,
+ "USB power");
+ ath79_register_usb();
+}
+
+MIPS_MACHINE(ATH79_MACH_QIHOO_C301, "QIHOO-C301", "Qihoo 360 C301",
+ qihoo_c301_setup);
diff --git a/target/linux/ar71xx/generic/profiles/qihoo.mk b/target/linux/ar71xx/generic/profiles/qihoo.mk
new file mode 100644
index 0000000..0ec778a
--- /dev/null
+++ b/target/linux/ar71xx/generic/profiles/qihoo.mk
@@ -0,0 +1,16 @@
+#
+# Copyright (C) 2013 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/QIHOO360
+ NAME:=Qihoo 360 C301
+ PACKAGES:=kmod-usb-core kmod-usb2 kmod-ledtrig-usbdev kmod-ath10k
+endef
+
+define Profile/QIHOO360/Description
+ Package set optimized for the Qihoo 360 C301 device.
+endef
+$(eval $(call Profile,QIHOO360))
diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile
index 683c238..d56585e 100644
--- a/target/linux/ar71xx/image/Makefile
+++ b/target/linux/ar71xx/image/Makefile
@@ -290,6 +290,7 @@ zcn1523h_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,6208k(rootfs
mynet_n600_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdata)ro,64k(devconf)ro,15872k(firmware),64k(radiocfg)ro
mynet_rext_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,7808k(firmware),64k(nvram)ro,64k(ART)ro,6848k at 0x130000(filesystem)
zyx_nbg6716_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(env)ro,64k(RFdata)ro,-(nbu);ar934x-nfc:2048k(zyxel_rfsd),2048k(romd),1024k(header),2048k(kernel),-(ubi)
+qihoo_c301_mtdlayout=mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(devdata),64k(devconf),15744k(firmware),64k(warm_start),64k(action_image_config),64k(radiocfg)ro;spi0.1:15360k(upgrade2),1024k(privatedata)
define Image/BuildKernel
@@ -1156,6 +1157,8 @@ $(eval $(call SingleProfile,Planex,64kraw,MZKW300NH,mzk-w300nh,MZK-W300NH,ttyS0,
$(eval $(call SingleProfile,Seama,64k,MYNETN600,mynet-n600,MYNET-N600,ttyS0,115200,$$(mynet_n600_mtdlayout),wrgnd16_wd_db600,1310720,16187392))
$(eval $(call SingleProfile,Seama,64k,MYNETN750,mynet-n750,MYNET-N750,ttyS0,115200,$$(mynet_n600_mtdlayout),wrgnd13_wd_av,1310720,16187392))
+$(eval $(call SingleProfile,Seama,64k,QIHOO360,qihoo-c301,QIHOO-C301,ttyS0,115200,$$(qihoo_c301_mtdlayout),wrgac26_qihoo360_360rg,1310720,16121856))
+
$(eval $(call SingleProfile,Senao,squashfs-only,EAP300V2,eap300v2,EAP300V2,ttyS0,115200,$$(eap300v2_mtdlayout)))
$(eval $(call SingleProfile,TPLINKOLD,squashfs-only,TLWR841NV15,tl-wr841nd-v1.5,TL-WR841N-v1.5,ttyS0,115200,0x08410002,2,4M))
diff --git a/target/linux/ar71xx/patches-3.10/601-MIPS-ath79-add-more-register-defines.patch b/target/linux/ar71xx/patches-3.10/601-MIPS-ath79-add-more-register-defines.patch
index 81a997b..214aa73 100644
--- a/target/linux/ar71xx/patches-3.10/601-MIPS-ath79-add-more-register-defines.patch
+++ b/target/linux/ar71xx/patches-3.10/601-MIPS-ath79-add-more-register-defines.patch
@@ -207,7 +207,7 @@
#define AR934X_GPIO_REG_FUNC 0x6c
#define AR71XX_GPIO_COUNT 16
-@@ -561,4 +664,148 @@
+@@ -561,4 +664,149 @@
#define AR934X_SRIF_DPLL2_OUTDIV_SHIFT 13
#define AR934X_SRIF_DPLL2_OUTDIV_MASK 0x7
@@ -279,6 +279,7 @@
+#define AR934X_GPIO_FUNC_JTAG_DISABLE BIT(1)
+
+#define AR934X_GPIO_OUT_GPIO 0
++#define AR934X_GPIO_OUT_SPI_CS1 7
+#define AR934X_GPIO_OUT_LED_LINK0 41
+#define AR934X_GPIO_OUT_LED_LINK1 42
+#define AR934X_GPIO_OUT_LED_LINK2 43
diff --git a/target/linux/ar71xx/patches-3.10/726-MIPS-ath79-add-qihoo-360-c301-support.patch b/target/linux/ar71xx/patches-3.10/726-MIPS-ath79-add-qihoo-360-c301-support.patch
new file mode 100644
index 0000000..6be83b0
--- /dev/null
+++ b/target/linux/ar71xx/patches-3.10/726-MIPS-ath79-add-qihoo-360-c301-support.patch
@@ -0,0 +1,40 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -1034,6 +1034,17 @@
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
++config ATH79_MACH_QIHOO_C301
++ bool "Qihoo 360 C301 board support"
++ select SOC_AR934X
++ select ATH79_DEV_ETH
++ select ATH79_DEV_GPIO_BUTTONS
++ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_M25P80
++ select ATH79_DEV_WMAC
++ select ATH79_DEV_USB
++ select ATH79_NVRAM
++
+ endmenu
+
+ config SOC_AR71XX
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -80,6 +80,7 @@
+ ATH79_MACH_OM5P, /* OpenMesh OM5P */
+ ATH79_MACH_PB42, /* Atheros PB42 */
+ ATH79_MACH_PB92, /* Atheros PB92 */
++ ATH79_MACH_QIHOO_C301, /* Qihoo 360 C301 */
+ ATH79_MACH_RB_411, /* MikroTik RouterBOARD 411/411A/411AH */
+ ATH79_MACH_RB_411U, /* MikroTik RouterBOARD 411U */
+ ATH79_MACH_RB_433, /* MikroTik RouterBOARD 433/433AH */
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -85,6 +85,7 @@
+ obj-$(CONFIG_ATH79_MACH_PB42) += mach-pb42.o
+ obj-$(CONFIG_ATH79_MACH_PB44) += mach-pb44.o
+ obj-$(CONFIG_ATH79_MACH_PB92) += mach-pb92.o
++obj-$(CONFIG_ATH79_MACH_QIHOO_C301) += mach-qihoo-c301.o
+ obj-$(CONFIG_ATH79_MACH_RB4XX) += mach-rb4xx.o
+ obj-$(CONFIG_ATH79_MACH_RB750) += mach-rb750.o
+ obj-$(CONFIG_ATH79_MACH_RB91X) += mach-rb91x.o
diff --git a/target/linux/ar71xx/patches-3.14/601-MIPS-ath79-add-more-register-defines.patch b/target/linux/ar71xx/patches-3.14/601-MIPS-ath79-add-more-register-defines.patch
index 79e53b3..2dec020 100644
--- a/target/linux/ar71xx/patches-3.14/601-MIPS-ath79-add-more-register-defines.patch
+++ b/target/linux/ar71xx/patches-3.14/601-MIPS-ath79-add-more-register-defines.patch
@@ -207,7 +207,7 @@
#define AR934X_GPIO_REG_FUNC 0x6c
#define AR71XX_GPIO_COUNT 16
-@@ -560,4 +663,148 @@
+@@ -560,4 +663,149 @@
#define AR934X_SRIF_DPLL2_OUTDIV_SHIFT 13
#define AR934X_SRIF_DPLL2_OUTDIV_MASK 0x7
@@ -279,6 +279,7 @@
+#define AR934X_GPIO_FUNC_JTAG_DISABLE BIT(1)
+
+#define AR934X_GPIO_OUT_GPIO 0
++#define AR934X_GPIO_OUT_SPI_CS1 7
+#define AR934X_GPIO_OUT_LED_LINK0 41
+#define AR934X_GPIO_OUT_LED_LINK1 42
+#define AR934X_GPIO_OUT_LED_LINK2 43
diff --git a/target/linux/ar71xx/patches-3.14/726-MIPS-ath79-add-qihoo-360-c301-support.patch b/target/linux/ar71xx/patches-3.14/726-MIPS-ath79-add-qihoo-360-c301-support.patch
new file mode 100644
index 0000000..6be83b0
--- /dev/null
+++ b/target/linux/ar71xx/patches-3.14/726-MIPS-ath79-add-qihoo-360-c301-support.patch
@@ -0,0 +1,40 @@
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -1034,6 +1034,17 @@
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
++config ATH79_MACH_QIHOO_C301
++ bool "Qihoo 360 C301 board support"
++ select SOC_AR934X
++ select ATH79_DEV_ETH
++ select ATH79_DEV_GPIO_BUTTONS
++ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_M25P80
++ select ATH79_DEV_WMAC
++ select ATH79_DEV_USB
++ select ATH79_NVRAM
++
+ endmenu
+
+ config SOC_AR71XX
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -80,6 +80,7 @@
+ ATH79_MACH_OM5P, /* OpenMesh OM5P */
+ ATH79_MACH_PB42, /* Atheros PB42 */
+ ATH79_MACH_PB92, /* Atheros PB92 */
++ ATH79_MACH_QIHOO_C301, /* Qihoo 360 C301 */
+ ATH79_MACH_RB_411, /* MikroTik RouterBOARD 411/411A/411AH */
+ ATH79_MACH_RB_411U, /* MikroTik RouterBOARD 411U */
+ ATH79_MACH_RB_433, /* MikroTik RouterBOARD 433/433AH */
+--- a/arch/mips/ath79/Makefile
++++ b/arch/mips/ath79/Makefile
+@@ -85,6 +85,7 @@
+ obj-$(CONFIG_ATH79_MACH_PB42) += mach-pb42.o
+ obj-$(CONFIG_ATH79_MACH_PB44) += mach-pb44.o
+ obj-$(CONFIG_ATH79_MACH_PB92) += mach-pb92.o
++obj-$(CONFIG_ATH79_MACH_QIHOO_C301) += mach-qihoo-c301.o
+ obj-$(CONFIG_ATH79_MACH_RB4XX) += mach-rb4xx.o
+ obj-$(CONFIG_ATH79_MACH_RB750) += mach-rb750.o
+ obj-$(CONFIG_ATH79_MACH_RB91X) += mach-rb91x.o
--
2.1.0.GIT
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list