[OpenWrt-Devel] MTD mounting problem on ar71xx and kernel 3.14.x.
Paul Blazejowski
paulb at blazebox.homeip.net
Thu Oct 2 12:45:08 EDT 2014
Hello all,
A while back i have created a ticket
(https://dev.openwrt.org/ticket/17609) detailing kernel 3.14.x failure
to boot on ar71xx (wndr3700v4 router) platform. Today i have
successfully used serial console attached to the router and got a boot
log which shows a wrong checksum of kernel image when trying to attach
it from UBI to MTD, please see output below ... i hope this helps in
identifying and narrows the issue for a possible fix.
Cheers!
-paul
U-Boot 1.1.4 (Jun 21 2012 - 11:09:33)
DNI HW ID: 29763948 flash 128MB RAM 128MB U-boot dni29 V1.8
DRAM: 128 MB
Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010
Atheros Communications, Ltd.
Ath Nand ID[87ff0178]: 2c:f1:80:95:02
ONFI MICRON MT29F1G08ABADAWP
Micron NAND 128MiB 3,3V 8-bit [128MB]
====== NAND Parameters ======
sc = 0x87ff0158 bbt = 0x87f68008 bbt_size = 0x100 nf_ctrl = 0x344
page = 0x800 block = 0x20000 oob = 0x40
size = 128MB
Setting 0xb8116290 to 0x4a942d0f
Using default environment
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
4096 bytes read: OK
Fetching MAC Address from 0x87fe7928
wasp reset mask:c02300
WASP ----> S17 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 44:94:fc:73:9a:fc
athrs17_reg_init: complete
eth0 up
eth0
Hit any key to stop autoboot: 0
dup 1 speed 1000
Client starts...[Listening] for ADVERTISE...checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
Tchecksum bad
checksum bad
TT
Retry count exceeded; boot the image as usual
nmrp server is stopped or failed !
Loading from device 0: ath-nand (offset 0x6c0000)
** check kernel image **
Verifying Checksum ... OK
** check rootfs image **
Verifying Checksum ... OK
## Booting image at 81000000 ...
Image Name: MIPS OpenWrt Linux-3.10.55
Created: 2014-09-30 15:48:31 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1965951 Bytes = 1.9 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.55 (diffie at blaze) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42682) ) #1 Tue Sep 30 11:48:14 EDT
2014
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:560.000MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 32512
[ 0.000000] Kernel command line: board=WNDR3700_V4
console=ttyS0,115200
mtdparts=ar934x-nfc:256k(u-boot)ro,256k(u-boot-env)ro,256k(caldata),512k(pot),2048k(language),512k(config),3072k(traffic_meter),2048k(kernel),121856k(ubi),123904k at 0x6c0000(firmware),256k(caldata_backup),-(reserved) rootfstype=squashfs noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536
bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 125868k/131072k available (2570k kernel code,
5204k reserved, 653k data, 228k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is NETGEAR WNDR3700v4
[ 0.300000] bio: create slab <bio-0> at 0
[ 0.310000] Switching to clocksource MIPS
[ 0.310000] NET: Registered protocol family 2
[ 0.320000] TCP established hash table entries: 1024 (order: 1, 8192
bytes)
[ 0.320000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.330000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.330000] TCP: reno registered
[ 0.340000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.340000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.350000] NET: Registered protocol family 1
[ 0.370000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.370000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.380000] msgmni has been set to 245
[ 0.390000] io scheduler noop registered
[ 0.390000] io scheduler deadline registered (default)
[ 0.400000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.420000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a
16550A
[ 0.430000] console [ttyS0] enabled, bootconsole disabled
[ 0.430000] console [ttyS0] enabled, bootconsole disabled
[ 0.450000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron
NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 0.460000] Scanning device for bad blocks
[ 0.550000] mtd: ar934x-nfc: skipping zero sized partition
[ 0.550000] 11 cmdlinepart partitions found on MTD device ar934x-nfc
[ 0.560000] Creating 11 MTD partitions on "ar934x-nfc":
[ 0.560000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.570000] 0x000000040000-0x000000080000 : "u-boot-env"
[ 0.580000] 0x000000080000-0x0000000c0000 : "caldata"
[ 0.580000] 0x0000000c0000-0x000000140000 : "pot"
[ 0.590000] 0x000000140000-0x000000340000 : "language"
[ 0.600000] 0x000000340000-0x0000003c0000 : "config"
[ 0.600000] 0x0000003c0000-0x0000006c0000 : "traffic_meter"
[ 0.610000] 0x0000006c0000-0x0000008c0000 : "kernel"
[ 0.620000] 0x0000008c0000-0x000007fc0000 : "ubi"
[ 0.620000] 0x0000006c0000-0x000007fc0000 : "firmware"
[ 1.770000] 0x000007fc0000-0x000008000000 : "caldata_backup"
[ 1.810000] switch0: Atheros AR8327 rev. 4 switch registered on
ag71xx-mdio.0
[ 3.010000] libphy: ag71xx_mdio: probed
[ 3.560000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00
[uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 3.570000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 3.580000] TCP: cubic registered
[ 3.590000] NET: Registered protocol family 17
[ 3.590000] 8021q: 802.1Q VLAN Support v1.8
[ 3.600000] UBI: auto-attach mtd8
[ 3.600000] UBI: attaching mtd8 to ubi0
[ 3.710000] UBI: EOF marker found, PEBs from 89 will be erased
[ 3.720000] UBI: scanning is finished
[ 3.750000] UBI: volume 1 ("rootfs_data") re-sized from 9 to 841
LEBs
[ 3.760000] UBI: attached mtd8 (name "ubi", size 119 MiB) to ubi0
[ 3.770000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976
bytes
[ 3.770000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size
2048
[ 3.780000] UBI: VID header offset: 2048 (aligned 2048), data offset:
4096
[ 3.790000] UBI: good PEBs: 952, bad PEBs: 0, corrupted PEBs: 0
[ 3.790000] UBI: user volume: 2, internal volumes: 1, max. volumes
count: 128
[ 3.800000] UBI: max/mean erase counter: 1/0, WL threshold: 4096,
image sequence number: 1122340664
[ 3.810000] UBI: available PEBs: 0, total reserved PEBs: 952, PEBs
reserved for bad PEB handling: 20
[ 3.820000] UBI: background thread "ubi_bgt0d" started, PID 276
[ 3.830000] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[ 3.830000] ubiblock: device ubiblock0_0 (rootfs) set to be root
filesystem
[ 3.860000] VFS: Mounted root (squashfs filesystem) readonly on
device 254:0.
[ 3.870000] Freeing unused kernel memory: 228K (80387000 - 803c0000)
procd: Console is alive
procd: - watchdog -
[ 7.710000] usbcore: registered new interface driver usbfs
[ 7.720000] usbcore: registered new interface driver hub
[ 7.730000] usbcore: registered new device driver usb
[ 7.810000] SGI XFS with security attributes, large block/inode
numbers, no debug enabled
[ 7.840000] SCSI subsystem initialized
[ 7.860000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[ 7.870000] ehci-platform: EHCI generic platform driver
[ 7.870000] ehci-platform ehci-platform: EHCI Host Controller
[ 7.880000] ehci-platform ehci-platform: new USB bus registered,
assigned bus number 1
[ 7.890000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 7.910000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 7.910000] hub 1-0:1.0: USB hub found
[ 7.920000] hub 1-0:1.0: 1 port detected
[ 7.930000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.950000] usbcore: registered new interface driver usb-storage
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
[ 9.560000] eth0: link up (1000Mbps/Full duplex)
kmod: ran 1 iterations
block: extroot: unable to locate rootfs mtdblock
[ 12.230000] UBIFS: default file-system created
[ 12.230000] UBIFS: background thread "ubifs_bgt0_1" started, PID 386
[ 12.430000] UBIFS: mounted UBI device 0, volume 1, name
"rootfs_data"
[ 12.440000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O
unit sizes: 2048 bytes/2048 bytes
[ 12.450000] UBIFS: FS size: 105390080 bytes (100 MiB, 830 LEBs),
journal size 5332992 bytes (5 MiB, 42 LEBs)
[ 12.460000] UBIFS: reserved for root: 4952683 bytes (4836 KiB)
[ 12.460000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID
C4A3F395-71FB-4CE9-8CA7-236ECAA45C3B, small LPT model
switching to overlay
[ 12.500000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
BusyBox v1.22.1 (2014-09-30 10:39:48 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (14.07, r42682)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@(none):/# [ 17.040000] NET: Registered protocol family 38
[ 17.110000] NET: Registered protocol family 10
[ 17.140000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 17.160000] Initializing XFRM netlink socket
[ 17.170000] NET: Registered protocol family 15
[ 17.180000] tun: Universal TUN/TAP device driver, 1.6
[ 17.180000] tun: (C) 1999-2004 Max Krasnyansky <maxk at qualcomm.com>
[ 17.250000] l2tp_core: L2TP core driver, V2.0
[ 17.270000] l2tp_netlink: L2TP netlink interface
[ 17.270000] sit: IPv6 over IPv4 tunneling driver
[ 17.300000] gre: GRE over IPv4 demultiplexor driver
[ 17.330000] ip_gre: GRE over IPv4 tunneling driver
[ 17.340000] ip6_gre: GRE over IPv6 tunneling driver
[ 17.370000] NET: Registered protocol family 5
[ 17.380000] ipddp.c:v0.01 8/28/97 Bradford W. Johnson
<johns393 at maroon.tc.umn.edu>
[ 17.390000] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson
<johns393 at maroon.tc.umn.edu>
[ 17.420000] nf_conntrack version 0.5.0 (1970 buckets, 7880 max)
[ 17.440000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.590000] Netfilter messages via NETLINK v0.30.
[ 17.600000] ip_set: protocol 6
[ 17.830000] batman_adv: B.A.T.M.A.N. advanced 2014.3.0 (compatibility
version 15) loaded
[ 17.870000] u32 classifier
[ 17.870000] input device check on
[ 17.880000] Actions configured
[ 17.890000] Mirror/redirect action on
[ 17.890000] Failed to load ipt action
[ 17.960000] fuse init (API version 7.22)
[ 17.980000] arp_tables: (C) 2002 David S. Miller
[ 18.000000] usbcore: registered new interface driver cdc_acm
[ 18.010000] cdc_acm: USB Abstract Control Model driver for USB modems
and ISDN adapters
[ 18.050000] usbcore: registered new interface driver cdc_wdm
[ 18.070000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 18.080000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 18.100000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.130000] ctnetlink v0.93: registering with nfnetlink.
[ 18.190000] usbcore: registered new interface driver ums-alauda
[ 18.200000] usbcore: registered new interface driver ums-cypress
[ 18.220000] usbcore: registered new interface driver ums-datafab
[ 18.230000] usbcore: registered new interface driver ums-freecom
[ 18.250000] usbcore: registered new interface driver ums-isd200
[ 18.260000] usbcore: registered new interface driver ums-jumpshot
[ 18.280000] usbcore: registered new interface driver ums-karma
[ 18.300000] usbcore: registered new interface driver ums-sddr09
[ 18.310000] usbcore: registered new interface driver ums-sddr55
[ 18.310000] usbcore: registered new interface driver ums-usbat
[ 18.330000] usbcore: registered new interface driver usblp
[ 18.390000] usbcore: registered new interface driver usbserial
[ 18.410000] usbcore: registered new interface driver
usbserial_generic
[ 18.410000] usbserial: USB Serial support registered for generic
[ 18.580000] xt_time: kernel timezone is -0000
[ 18.630000] usbcore: registered new interface driver ftdi_sio
[ 18.650000] usbserial: USB Serial support registered for FTDI USB
Serial Device
[ 18.670000] cfg80211: Calling CRDA to update world regulatory domain
[ 18.730000] cfg80211: World regulatory domain updated:
[ 18.730000] cfg80211: DFS Master region: unset
[ 18.730000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 18.740000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 18.750000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 18.760000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm), (N/A)
[ 18.770000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (N/A)
[ 18.780000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 18.790000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 18.790000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm), (N/A)
[ 18.800000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 18.850000] usbcore: registered new interface driver pl2303
[ 18.850000] usbserial: USB Serial support registered for pl2303
[ 18.870000] PPP generic driver version 2.4.2
[ 18.880000] PPP MPPE Compression module registered
[ 18.880000] NET: Registered protocol family 24
[ 18.900000] PPTP driver version 0.8.5
[ 18.940000] usbcore: registered new interface driver sierra
[ 18.940000] usbserial: USB Serial support registered for Sierra USB
modem
[ 18.960000] usbcore: registered new interface driver sierra_net
[ 19.040000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 19.060000] usbcore: registered new interface driver option
[ 19.060000] usbserial: USB Serial support registered for GSM modem
(1-port)
[ 19.080000] usbcore: registered new interface driver qcserial
[ 19.100000] usbserial: USB Serial support registered for Qualcomm USB
modem
[ 19.360000] cfg80211: Calling CRDA for country: US
[ 19.370000] cfg80211: Regulatory domain changed to country: US
[ 19.370000] cfg80211: DFS Master region: FCC
[ 19.380000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 19.390000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz),
(N/A, 3000 mBm), (N/A)
[ 19.390000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz),
(N/A, 1700 mBm), (N/A)
[ 19.400000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz),
(N/A, 2300 mBm), (0 s)
[ 19.410000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz),
(N/A, 3000 mBm), (N/A)
[ 19.420000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 19.430000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000,
irq=47
[ 28.840000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 28.860000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 28.860000] device eth0.1 entered promiscuous mode
[ 28.870000] device eth0 entered promiscuous mode
[ 28.880000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 29.010000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 30.310000] eth0: link up (1000Mbps/Full duplex)
[ 30.440000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 30.450000] br-lan: port 1(eth0.1) entered forwarding state
[ 30.450000] br-lan: port 1(eth0.1) entered forwarding state
[ 30.460000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes
ready
[ 30.460000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes
ready
[ 30.470000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes
ready
[ 32.450000] br-lan: port 1(eth0.1) entered forwarding state
root at OpenWrt:/#
root at OpenWrt:/# [ 46.150000] device br-lan entered promiscuous mode
procd: - init complete -
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: This is a digitally signed message part
URL: <http://lists.infradead.org/pipermail/openwrt-devel/attachments/20141002/f29e3548/attachment.sig>
-------------- next part --------------
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list