[OpenWrt-Devel] [PATCH v2 1/2] firmware-utils: add new tool tplink-safeloader for the new TP-LINK Pharos devices (CPE210/220/510/520)
Matthias Schiffer
mschiffer at universe-factory.net
Tue Nov 25 14:53:46 EST 2014
The new TP-LINK Pharos series uses a new bootloader, the "TP-LINK Safeloader".
It uses an advanced firmware image format, containing an image partition table
and a flash partition table (and image partitions are mapped to the
corresponding flash partitions). The exact image format is documented in the
source code.
Furthermore, the bootloader expects the kernel image as an ELF executable.
Signed-off-by: Matthias Schiffer <mschiffer at universe-factory.net>
---
tools/firmware-utils/Makefile | 1 +
tools/firmware-utils/src/tplink-safeloader.c | 538 +++++++++++++++++++++++++++
2 files changed, 539 insertions(+)
create mode 100644 tools/firmware-utils/src/tplink-safeloader.c
diff --git a/tools/firmware-utils/Makefile b/tools/firmware-utils/Makefile
index 65b7c15..988c625 100644
--- a/tools/firmware-utils/Makefile
+++ b/tools/firmware-utils/Makefile
@@ -41,6 +41,7 @@ define Host/Compile
$(call cc,mkplanexfw sha1)
$(call cc,mktplinkfw md5)
$(call cc,mktplinkfw2 md5)
+ $(call cc,tplink-safeloader md5, -Wall)
$(call cc,pc1crypt)
$(call cc,osbridge-crc)
$(call cc,wrt400n cyg_crc32)
diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c
new file mode 100644
index 0000000..23d703f
--- /dev/null
+++ b/tools/firmware-utils/src/tplink-safeloader.c
@@ -0,0 +1,538 @@
+/*
+ Copyright (c) 2014, Matthias Schiffer <mschiffer at universe-factory.net>
+ All rights reserved.
+
+ Redistribution and use in source and binary forms, with or without
+ modification, are permitted provided that the following conditions are met:
+
+ 1. Redistributions of source code must retain the above copyright notice,
+ this list of conditions and the following disclaimer.
+ 2. Redistributions in binary form must reproduce the above copyright notice,
+ this list of conditions and the following disclaimer in the documentation
+ and/or other materials provided with the distribution.
+
+ THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+*/
+
+
+/*
+ tplink-safeloader
+
+ Image generation tool for the TP-LINK SafeLoader as seen on
+ TP-LINK Pharos devices (CPE210/220/510/520)
+*/
+
+
+#include <assert.h>
+#include <errno.h>
+#include <error.h>
+#include <stdbool.h>
+#include <stdio.h>
+#include <stdint.h>
+#include <stdlib.h>
+#include <string.h>
+#include <time.h>
+#include <unistd.h>
+
+#include <arpa/inet.h>
+
+#include <sys/types.h>
+#include <sys/stat.h>
+
+#include "md5.h"
+
+
+#define ALIGN(x,a) ({ typeof(a) __a = (a); (((x) + __a - 1) & ~(__a - 1)); })
+
+
+/** An image partition table entry */
+struct image_partition_entry {
+ const char *name;
+ size_t size;
+ uint8_t *data;
+};
+
+/** A flash partition table entry */
+struct flash_partition_entry {
+ const char *name;
+ uint32_t base;
+ uint32_t size;
+};
+
+
+/** The content of the soft-version structure */
+struct __attribute__((__packed__)) soft_version {
+ uint32_t magic;
+ uint32_t zero;
+ uint8_t pad1;
+ uint8_t version_major;
+ uint8_t version_minor;
+ uint8_t version_patch;
+ uint8_t year_hi;
+ uint8_t year_lo;
+ uint8_t month;
+ uint8_t day;
+ uint32_t rev;
+ uint8_t pad2;
+};
+
+
+static const uint8_t jffs2_eof_mark[4] = {0xde, 0xad, 0xc0, 0xde};
+
+
+/**
+ Salt for the MD5 hash
+
+ Fortunately, TP-LINK seems to use the same salt for most devices which use
+ the new image format.
+*/
+static const uint8_t md5_salt[16] = {
+ 0x7a, 0x2b, 0x15, 0xed,
+ 0x9b, 0x98, 0x59, 0x6d,
+ 0xe5, 0x04, 0xab, 0x44,
+ 0xac, 0x2a, 0x9f, 0x4e,
+};
+
+
+/** Vendor information for CPE210/220/510/520 */
+static const unsigned char cpe510_vendor[] = "\x00\x00\x00\x1f""CPE510(TP-LINK|UN|N300-5):1.0\r\n";
+
+
+/**
+ The flash partition table for CPE210/220/510/520;
+ it is the same as the one used by the stock images.
+*/
+static const struct flash_partition_entry cpe510_partitions[] = {
+ {"fs-uboot", 0x00000, 0x20000},
+ {"partition-table", 0x20000, 0x02000},
+ {"default-mac", 0x30000, 0x00020},
+ {"product-info", 0x31100, 0x00100},
+ {"signature", 0x32000, 0x00400},
+ {"os-image", 0x40000, 0x170000},
+ {"soft-version", 0x1b0000, 0x00100},
+ {"support-list", 0x1b1000, 0x00400},
+ {"file-system", 0x1c0000, 0x600000},
+ {"user-config", 0x7c0000, 0x10000},
+ {"default-config", 0x7d0000, 0x10000},
+ {"log", 0x7e0000, 0x10000},
+ {"radio", 0x7f0000, 0x10000},
+ {NULL, 0, 0}
+};
+
+/**
+ The support list for CPE210/220/510/520
+
+ The stock images also contain strings for two more devices: BS510 and BS210.
+ At the moment, there exists no public information about these devices.
+*/
+static const unsigned char cpe510_support_list[] =
+ "\x00\x00\x00\xc8\x00\x00\x00\x00"
+ "SupportList:\r\n"
+ "CPE510(TP-LINK|UN|N300-5):1.0\r\n"
+ "CPE520(TP-LINK|UN|N300-5):1.0\r\n"
+ "CPE210(TP-LINK|UN|N300-2):1.0\r\n"
+ "CPE220(TP-LINK|UN|N300-2):1.0\r\n"
+ "\r\n\xff";
+
+
+/** Allocates a new image partition */
+struct image_partition_entry alloc_image_partition(const char *name, size_t len) {
+ struct image_partition_entry entry = {name, len, malloc(len)};
+ if (!entry.data)
+ error(1, errno, "malloc");
+
+ return entry;
+}
+
+/** Frees an image partition */
+void free_image_partition(struct image_partition_entry entry) {
+ free(entry.data);
+}
+
+/** Generates the partition-table partition */
+struct image_partition_entry make_partition_table(const struct flash_partition_entry *p) {
+ struct image_partition_entry entry = alloc_image_partition("partition-table", 0x800);
+
+ char *s = (char *)entry.data, *end = (char *)(s+entry.size);
+
+ *(s++) = 0x00;
+ *(s++) = 0x04;
+ *(s++) = 0x00;
+ *(s++) = 0x00;
+
+ size_t i;
+ for (i = 0; p[i].name; i++) {
+ size_t len = end-s;
+ size_t w = snprintf(s, len, "partition %s base 0x%05x size 0x%05x\n", p[i].name, p[i].base, p[i].size);
+
+ if (w > len-1)
+ error(1, 0, "flash partition table overflow?");
+
+ s += w;
+ }
+
+ s++;
+
+ memset(s, 0xff, end-s);
+
+ return entry;
+}
+
+
+/** Generates a binary-coded decimal representation of an integer in the range [0, 99] */
+static inline uint8_t bcd(uint8_t v) {
+ return 0x10 * (v/10) + v%10;
+}
+
+
+/** Generates the soft-version partition */
+struct image_partition_entry make_soft_version(uint32_t rev) {
+ struct image_partition_entry entry = alloc_image_partition("soft-version", sizeof(struct soft_version));
+ struct soft_version *s = (struct soft_version *)entry.data;
+
+ time_t t;
+ if (time(&t) == (time_t)(-1))
+ error(1, errno, "time");
+
+ struct tm *tm = localtime(&t);
+
+ s->magic = htonl(0x0000000c);
+ s->zero = 0;
+ s->pad1 = 0xff;
+
+ s->version_major = 0;
+ s->version_minor = 0;
+ s->version_patch = 0;
+
+ s->year_hi = bcd((1900+tm->tm_year)/100);
+ s->year_lo = bcd(tm->tm_year%100);
+ s->month = bcd(tm->tm_mon+1);
+ s->day = bcd(tm->tm_mday);
+ s->rev = htonl(rev);
+
+ s->pad2 = 0xff;
+
+ return entry;
+}
+
+/** Generates the support-list partition */
+struct image_partition_entry make_support_list(const unsigned char *support_list, size_t len) {
+ struct image_partition_entry entry = alloc_image_partition("support-list", len);
+ memcpy(entry.data, support_list, len);
+ return entry;
+}
+
+/** Creates a new image partition with an arbitrary name from a file */
+struct image_partition_entry read_file(const char *part_name, const char *filename, bool add_jffs2_eof) {
+ struct stat statbuf;
+
+ if (stat(filename, &statbuf) < 0)
+ error(1, errno, "unable to stat file `%s'", filename);
+
+ size_t len = statbuf.st_size;
+
+ if (add_jffs2_eof)
+ len = ALIGN(len, 0x10000) + sizeof(jffs2_eof_mark);
+
+ struct image_partition_entry entry = alloc_image_partition(part_name, len);
+
+ FILE *file = fopen(filename, "rb");
+ if (!file)
+ error(1, errno, "unable to open file `%s'", filename);
+
+ if (fread(entry.data, statbuf.st_size, 1, file) != 1)
+ error(1, errno, "unable to read file `%s'", filename);
+
+ if (add_jffs2_eof) {
+ uint8_t *eof = entry.data + statbuf.st_size, *end = entry.data+entry.size;
+
+ memset(eof, 0xff, end - eof - sizeof(jffs2_eof_mark));
+ memcpy(end - sizeof(jffs2_eof_mark), jffs2_eof_mark, sizeof(jffs2_eof_mark));
+ }
+
+ fclose(file);
+
+ return entry;
+}
+
+
+/**
+ Copies a list of image partitions into an image buffer and generates the image partition table while doing so
+
+ Example image partition table:
+
+ fwup-ptn partition-table base 0x00800 size 0x00800
+ fwup-ptn os-image base 0x01000 size 0x113b45
+ fwup-ptn file-system base 0x114b45 size 0x1d0004
+ fwup-ptn support-list base 0x2e4b49 size 0x000d1
+
+ Each line of the partition table is terminated with the bytes 09 0d 0a ("\t\r\n"),
+ the end of the partition table is marked with a zero byte.
+
+ The firmware image must contain at least the partition-table and support-list partitions
+ to be accepted. There aren't any alignment constraints for the image partitions.
+
+ The partition-table partition contains the actual flash layout; partitions
+ from the image partition table are mapped to the corresponding flash partitions during
+ the firmware upgrade. The support-list partition contains a list of devices supported by
+ the firmware image.
+
+ The base offsets in the firmware partition table are relative to the end
+ of the vendor information block, so the partition-table partition will
+ actually start at offset 0x1814 of the image.
+
+ I think partition-table must be the first partition in the firmware image.
+*/
+void put_partitions(uint8_t *buffer, const struct image_partition_entry *parts) {
+ size_t i;
+ char *image_pt = (char *)buffer, *end = image_pt + 0x800;
+
+ size_t base = 0x800;
+ for (i = 0; parts[i].name; i++) {
+ memcpy(buffer + base, parts[i].data, parts[i].size);
+
+ size_t len = end-image_pt;
+ size_t w = snprintf(image_pt, len, "fwup-ptn %s base 0x%05x size 0x%05x\t\r\n", parts[i].name, (unsigned)base, (unsigned)parts[i].size);
+
+ if (w > len-1)
+ error(1, 0, "image partition table overflow?");
+
+ image_pt += w;
+
+ base += parts[i].size;
+ }
+
+ image_pt++;
+
+ memset(image_pt, 0xff, end-image_pt);
+}
+
+/** Generates and writes the image MD5 checksum */
+void put_md5(uint8_t *md5, uint8_t *buffer, unsigned int len) {
+ MD5_CTX ctx;
+
+ MD5_Init(&ctx);
+ MD5_Update(&ctx, md5_salt, (unsigned int)sizeof(md5_salt));
+ MD5_Update(&ctx, buffer, len);
+ MD5_Final(md5, &ctx);
+}
+
+
+/**
+ Generates the firmware image in factory format
+
+ Image format:
+
+ Bytes (hex) Usage
+ ----------- -----
+ 0000-0003 Image size (4 bytes, big endian)
+ 0004-0013 MD5 hash (hash of a 16 byte salt and the image data starting with byte 0x14)
+ 0014-1013 Vendor information (4096 bytes, padded with 0xff; there seem to be older
+ (VxWorks-based) TP-LINK devices which use a smaller vendor information block)
+ 1014-1813 Image partition table (2048 bytes, padded with 0xff)
+ 1814-xxxx Firmware partitions
+*/
+void * generate_factory_image(const unsigned char *vendor, size_t vendor_len, const struct image_partition_entry *parts, size_t *len) {
+ *len = 0x1814;
+
+ size_t i;
+ for (i = 0; parts[i].name; i++)
+ *len += parts[i].size;
+
+ uint8_t *image = malloc(*len);
+ if (!image)
+ error(1, errno, "malloc");
+
+ image[0] = *len >> 24;
+ image[1] = *len >> 16;
+ image[2] = *len >> 8;
+ image[3] = *len;
+
+ memcpy(image+0x14, vendor, vendor_len);
+ memset(image+0x14+vendor_len, 0xff, 4096-vendor_len);
+
+ put_partitions(image + 0x1014, parts);
+ put_md5(image+0x04, image+0x14, *len-0x14);
+
+ return image;
+}
+
+/**
+ Generates the firmware image in sysupgrade format
+
+ This makes some assumptions about the provided flash and image partition tables and
+ should be generalized when TP-LINK starts building its safeloader into hardware with
+ different flash layouts.
+*/
+void * generate_sysupgrade_image(const struct flash_partition_entry *flash_parts, const struct image_partition_entry *image_parts, size_t *len) {
+ const struct flash_partition_entry *flash_os_image = &flash_parts[5];
+ const struct flash_partition_entry *flash_soft_version = &flash_parts[6];
+ const struct flash_partition_entry *flash_support_list = &flash_parts[7];
+ const struct flash_partition_entry *flash_file_system = &flash_parts[8];
+
+ const struct image_partition_entry *image_os_image = &image_parts[3];
+ const struct image_partition_entry *image_soft_version = &image_parts[1];
+ const struct image_partition_entry *image_support_list = &image_parts[2];
+ const struct image_partition_entry *image_file_system = &image_parts[4];
+
+ assert(strcmp(flash_os_image->name, "os-image") == 0);
+ assert(strcmp(flash_soft_version->name, "soft-version") == 0);
+ assert(strcmp(flash_support_list->name, "support-list") == 0);
+ assert(strcmp(flash_file_system->name, "file-system") == 0);
+
+ assert(strcmp(image_os_image->name, "os-image") == 0);
+ assert(strcmp(image_soft_version->name, "soft-version") == 0);
+ assert(strcmp(image_support_list->name, "support-list") == 0);
+ assert(strcmp(image_file_system->name, "file-system") == 0);
+
+ if (image_os_image->size > flash_os_image->size)
+ error(1, 0, "kernel image too big (more than %u bytes)", (unsigned)flash_os_image->size);
+ if (image_file_system->size > flash_file_system->size)
+ error(1, 0, "rootfs image too big (more than %u bytes)", (unsigned)flash_file_system->size);
+
+ *len = flash_file_system->base - flash_os_image->base + image_file_system->size;
+
+ uint8_t *image = malloc(*len);
+ if (!image)
+ error(1, errno, "malloc");
+
+ memset(image, 0xff, *len);
+
+ memcpy(image, image_os_image->data, image_os_image->size);
+ memcpy(image + flash_soft_version->base - flash_os_image->base, image_soft_version->data, image_soft_version->size);
+ memcpy(image + flash_support_list->base - flash_os_image->base, image_support_list->data, image_support_list->size);
+ memcpy(image + flash_file_system->base - flash_os_image->base, image_file_system->data, image_file_system->size);
+
+ return image;
+}
+
+
+/** Generates an image for CPE210/220/510/520 and writes it to a file */
+static void do_cpe510(const char *output, const char *kernel_image, const char *rootfs_image, uint32_t rev, bool add_jffs2_eof, bool sysupgrade) {
+ struct image_partition_entry parts[6] = {};
+
+ parts[0] = make_partition_table(cpe510_partitions);
+ parts[1] = make_soft_version(rev);
+ parts[2] = make_support_list(cpe510_support_list, sizeof(cpe510_support_list)-1);
+ parts[3] = read_file("os-image", kernel_image, false);
+ parts[4] = read_file("file-system", rootfs_image, add_jffs2_eof);
+
+ size_t len;
+ void *image;
+ if (sysupgrade)
+ image = generate_sysupgrade_image(cpe510_partitions, parts, &len);
+ else
+ image = generate_factory_image(cpe510_vendor, sizeof(cpe510_vendor)-1, parts, &len);
+
+ FILE *file = fopen(output, "wb");
+ if (!file)
+ error(1, errno, "unable to open output file");
+
+ if (fwrite(image, len, 1, file) != 1)
+ error(1, 0, "unable to write output file");
+
+ fclose(file);
+
+ free(image);
+
+ size_t i;
+ for (i = 0; parts[i].name; i++)
+ free_image_partition(parts[i]);
+}
+
+
+/** Usage output */
+void usage(const char *argv0) {
+ fprintf(stderr,
+ "Usage: %s [OPTIONS...]\n"
+ "\n"
+ "Options:\n"
+ " -B <board> create image for the board specified with <board>\n"
+ " -k <file> read kernel image from the file <file>\n"
+ " -r <file> read rootfs image from the file <file>\n"
+ " -o <file> write output to the file <file>\n"
+ " -V <rev> sets the revision number to <rev>\n"
+ " -j add jffs2 end-of-filesystem markers\n"
+ " -S create sysupgrade instead of factory image\n"
+ " -h show this help\n",
+ argv0
+ );
+};
+
+
+int main(int argc, char *argv[]) {
+ const char *board = NULL, *kernel_image = NULL, *rootfs_image = NULL, *output = NULL;
+ bool add_jffs2_eof = false, sysupgrade = false;
+ unsigned rev = 0;
+
+ while (true) {
+ int c;
+
+ c = getopt(argc, argv, "B:k:r:o:V:jSh");
+ if (c == -1)
+ break;
+
+ switch (c) {
+ case 'B':
+ board = optarg;
+ break;
+
+ case 'k':
+ kernel_image = optarg;
+ break;
+
+ case 'r':
+ rootfs_image = optarg;
+ break;
+
+ case 'o':
+ output = optarg;
+ break;
+
+ case 'V':
+ sscanf(optarg, "r%u", &rev);
+ break;
+
+ case 'j':
+ add_jffs2_eof = true;
+ break;
+
+ case 'S':
+ sysupgrade = true;
+ break;
+
+ case 'h':
+ usage(argv[0]);
+ return 0;
+
+ default:
+ usage(argv[0]);
+ return 1;
+ }
+ }
+
+ if (!board)
+ error(1, 0, "no board has been specified");
+ if (!kernel_image)
+ error(1, 0, "no kernel image has been specified");
+ if (!rootfs_image)
+ error(1, 0, "no rootfs image has been specified");
+ if (!output)
+ error(1, 0, "no output filename has been specified");
+
+ if (strcmp(board, "CPE510") == 0)
+ do_cpe510(output, kernel_image, rootfs_image, rev, add_jffs2_eof, sysupgrade);
+ else
+ error(1, 0, "unsupported board %s", board);
+
+ return 0;
+}
--
2.1.3
_______________________________________________
openwrt-devel mailing list
openwrt-devel at lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
More information about the openwrt-devel
mailing list